Emerson X-web300 Bedienungsanleitung Seite 94
- Seite / 102
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1592015300 User manual iCHILL 200 L GB r1.3 09/09/2005
Pg.94/106
41.37 ACP1 - ACP1 CONDENSER PUMP MINTENANCE
Label o the display
ACP1 (Condenser #1 pump maintenance)
ACP1 (Condenser #2 pump maintenance)
Origin
Pump running hours > Hour counter setpoint
Reset Hour reset in function menu
Restart Manual
Icona
Blinking
Action Alarm relay + buzzer ON
Regulation
Action Only display warning messages
Loads Not changed
41.38 ALARM RELAY AND BUZZER
Alarm relay / buzzer outputs
Origin Alarms still active
Alarms not reset
Reset relay alarm Whitout alarms
In stand- by or remote ON-O FF if AL42 = 1
Buzzer silencing By pushing one of the key of the front panel
The alarm relay is enabled only by configurating the corresponding output resource.
41.39 KEYABOARD ALARM
Alarm
code
keyaboard Alarm description
noL
No data communication between the keyaboard and the regulator.
Atr1
keyaboard n° 1 set up but not connected to regulator
Atr2
keyaboard n° 2 set up but not connected to regulator
42 AUTOMATIC TO MANUAL ALARM PROCEDURE
NUMBER OF EVENTS PER HOUR
Each hour counting is divided in 16 intervals, each made of 3600 / 16 = 225 seconds (3 minuts and 45 seconds).
1°Int 2°Int 3°Int 4°Int 5°Int 6°Int 7°Int 8°Int 9°Int 10°Int 11°Int 12°Int 13°Int 14°Int 15°Int 16°Int
After the unit start-up, each interval is marked as “not active”. During the interval counting, for 255seconds, if at least an alarm event
appears, the interval itself is marked “Active”.
Starting from the first interval the instrument calculates the 16 intervals and, at the end, it restats overwriting from the first.
In this way the last hour is always monitored and counted the active intervals. when the number of active intervals reaches the thresold
set with the corresponding parameter the alarm becomes manual.
By setting the thresold (parameter)=0 the alarm is manual from its first activation while if the thresold=16 the alarm is always automatic
(In this case, to change in manual, the thresold should be 17).
- DIXELL 1
- INDEX 2
- 4
- 1 GENERAL ADVICE 7
- 2 GENERAL FEATURES 8
- 2.1 MAIN FUNCTION 8
- Pg.10/106 10
- 4 USER INTERFACE 11
- Pg.12/106 12
- 4.4 KEY FUNCTION 14
- 4.5 KEY COMBINANTION 15
- 4.6 LED AND ICONS 15
- 4.7 DISPLAY AND ICONS 16
- 5 REMOTE TERMINAL 17
- 6 FIRST INSTALLING 17
- 6.2 RTC SETUP 17
- 7 WIRING CONNECTIONS 18
- 7.4 DIGITAL INPUTS 19
- Pg.20/106 20
- Pg.22/106 22
- 7.12 HOT KEY 64 CONNECTION 23
- 7.13 XJ485 CONNECTION 23
- Pg.24/106 24
- Pg.26/106 26
- 8.7 OTHER OUTPUTS 27
- 9 TABLE OF THE PARAMETERS 28
- Pg.30/106 30
- Pg.32/106 32
- Pg.34/106 34
- Pg.36/106 36
- Pg.38/106 38
- Pg.40/106 40
- Pg.42/106 42
- Enter the programming 42
- Pg.44/106 44
- Pg.46/106 46
- GRAPH: AUTOMATIC CHANGE OVER 46
- HOW THE CIRCUIT 1 OR 2 47
- 15 CUSTOM DISPLAY 48
- Pg.50/106 50
- HOW THE SET POINT VALUE 51
- ODIFY THE SET POINT 51
- 16.4 DISPLAY IN REMOTE OFF 52
- 17 FUNCTION MENU “ M” KEY 52
- 18 ENERGY SAVING 56
- 19 DYNAMIC SETPOINT 57
- 19.1 DYNAMIC SETPOINT GRAPH 58
- 20 AUXILIARY RELAYS 59
- Pg.60/106 60
- /RECOVERY 62
- 27 COMPRESSORS 64
- 27.1 COMPRESSORS START- UP 64
- 27.2 DIRECT START- UP 64
- 27.4 PART WINDING 65
- 27.7 STAR - DELTA START 65
- 28 CAPACITY CONTROL 66
- 28.1 MINIMUM LOAD START- UP 67
- 29 PUMP DOWN 68
- ACTIVATION 69
- UMP DOWN INFORMATION 70
- NLOADING DESCRIPTION 70
- NLOADING INFORMATION 70
- Pg.72/106 72
- FA26 Hot start differential 73
- 36 LOAD MAINTENANCE 74
- 37 CONDENSER FAN REGULATION 74
- OUTPUT FOR FAN CONTROL 75
- Pg.76/106 76
- 38 DEFROST CYCLE 77
- 38.1 FORCED DEFROST 77
- 38.2 COMBINED DEFROST 77
- 38.3 MANUAL DEFROST 78
- EFROST PARAMETER DESCRIPTION 79
- Pg.80/106 80
- 39 RECOVERY 81
- THE RECOVERY CYCLE 82
- 40.1 RECOVERY DISABLED 82
- AEFL evaporator flow alarm 83
- NOTE ABOUT THE FLOW ALARM 83
- 41.7 AEE EEPROM ALARM 84
- Significato label display 85
- 41.11 ARTF CLOCK FAILURE 86
- 41.12 ARTC CLOCK ALARM 87
- Pg.88/106 88
- Pg.90/106 90
- - PRESSURE SWITCH ALARM / 90
- Pg.92/106 92
- 41.38 ALARM RELAY AND BUZZER 94
- 41.39 KEYABOARD ALARM 94
- Pg.96/106 96
- Alarm description 96
- 44 BLACK-OUT 98
- 45 INSTALLING AND MOUNTING 98
- 45.1 PANEL CUT- OUT 98
- 45.4 METAL FRONT FRAME 99
- 46 ELECTRICAL CONNECTIONS 100
- 47 ACCESSORIES 100
- 47.3 TRANSFORMER 101
- 48 TECHNICAL DATA 102
Kommentare zu diesen Handbüchern
Verwandte Produkte und Handbücher für Vernetzung Emerson X-web300
Vernetzung Emerson X-web500 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
(166 Seiten)
Vernetzung Emerson FM-3 Spezifikationen
(110 Seiten)
(110 Seiten)
Vernetzung Emerson FM-3 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Vernetzung Emerson Liebert CW Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Vernetzung Emerson FM-3 Betriebsanweisung
(263 Seiten)
(263 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med