Emerson X-web300 Bedienungsanleitung Seite 55
- Seite / 102
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1592015300 User manual iCHILL 200 L GB r1.3 09/09/2005
17.16 READ-OUT OF THE PROPORTIONAL OUTPUT PERCENTAGE OF THE CONDENSER FAN
CONTROL
The proportional outputs of the two circuits, that control the fan speed, can be showed in the menu function.
Cond FUNCTION selects the proportional output 1 and 2.
Label involved in Cond function.
Cnd1 Proportional output status of the condenser fan of the circuit 1.
Cnd2 Proportional output status of the condenser fan of the circuit 2.
TO SEE THE OUTPUT PERCENTAGE:
Enter the function menu
1. Use the UP or DOWN keys to select
Cond.
2. Push SET key: the bottom display shows Cnd1, the top display shows the output percentage.
3. Use the UP or DOWN keys to select Cnd1 or Cnd2, the top display always shows the value, between 0% and 100%, of the
proportional output of the selected circuit.
4. To exit the Hour function push MENU key or wait the timeout.
17.17 READ-OUT OF THE FOUR PROPORTIONAL OUTPUT
The four proportional outputs, 4..20ma or 0-10V, can be showed in the menu function.
Pout FUNCTION selects the proportional outputs.
Label involved in Cond function:
Pou1 Proportional output for dumper control or to drive the external relay 1
Pou2 Proportional output for dumper control or to drive the external relay 2
Pou3 Proportional output for dumper control or to drive the external relay 3
Pou4 Proportional output for dumper control or to drive the external relay 4
The labels are displayed only if the corresponding output is present and configured.
TO SEE THE FOUR OUTPUT PERCENTAGE:
Enter the function menu
1. Use the UP or DOWN keys to select
Pout.
2. Push SET key: the bottom display shows Pou1, the top display shows the output percentage.
3. Use the UP or DOWN keys to select Pou1, Pou2, Pou3 or Pou4 the top display always shows the value, between 0% and
100%, of the proportional output of the selected circuit.
4. To exit the Hour function push MENU key or wait the timeout.
ATTENTION:
If the proportional output Pou1 - Pou2 - Pou3 - Pou4 are configured to drive an external relay the display will show 0=relay off
and 100=relay on.
17.18 READ-OUT OF THE TIME COUNTING TO THE NEXT DEFROST
The 2 times delay to next defrosts of the two circuits can be showed in the menu function.
dF FUNCTION time to next defrost.
Label involved in dF function:
dF1 delay time to next defrost of the circuit 1
dF2 delay time to next defrost of the circuit 2
The labels apperas on if the heat pump configuration is enabled.
Enter the function menu :
1. Use the UP or DOWN keys to select
dF
2. Push SET key: the dF1 label is showed on the top display, the bottom display shows the time delay to next defrost in minutes
/ seconds. The
icon is on.
3. Use the UP or DOWN keys to select dF1 or dF2.
4. To exit the Hour function push MENU key or wait the timeout.
17.19 READ-OUT OF THE PROBES CONFIGURED TO CONTROL AN AUXILIARY OUTPUT RELAY
The probe values, configured to control the auxiliary relay output, can be showed in the menu function.
uS FUNCTION temperature/pressure value of the control probe for auxiliary output.
Label involved in uS function:
uSt1 auxiliary probe value of the circuit 1
uSt2 auxiliary probe value of the circuit 2
Enter the function menu
1. Use the UP or DOWN keys to select uS.
2. Push SET key: the label uSt1 (temperature probe ) or uSP1 (Pressure probe) is showed on bottom display, the top display
shows the the temperature or pressure value.
3. Use the UP or DOWN keys to select uSt1 auxiliary probe for circuit 1or uSt2 auxiliary probe for circuit 2.
4. To exit the Hour function push MENU key or wait the timeout.
17.20 HOW TO DISPLAY THE TEMPAERATURE OF THE INTERNAL TEMPERAURE SENSOR OF
THE REMOTE TERMINALS 1 OR 2
Inside the funcion menu it is possible to see the ambient temperature detected by the NTC sensor
- DIXELL 1
- INDEX 2
- 4
- 1 GENERAL ADVICE 7
- 2 GENERAL FEATURES 8
- 2.1 MAIN FUNCTION 8
- Pg.10/106 10
- 4 USER INTERFACE 11
- Pg.12/106 12
- 4.4 KEY FUNCTION 14
- 4.5 KEY COMBINANTION 15
- 4.6 LED AND ICONS 15
- 4.7 DISPLAY AND ICONS 16
- 5 REMOTE TERMINAL 17
- 6 FIRST INSTALLING 17
- 6.2 RTC SETUP 17
- 7 WIRING CONNECTIONS 18
- 7.4 DIGITAL INPUTS 19
- Pg.20/106 20
- Pg.22/106 22
- 7.12 HOT KEY 64 CONNECTION 23
- 7.13 XJ485 CONNECTION 23
- Pg.24/106 24
- Pg.26/106 26
- 8.7 OTHER OUTPUTS 27
- 9 TABLE OF THE PARAMETERS 28
- Pg.30/106 30
- Pg.32/106 32
- Pg.34/106 34
- Pg.36/106 36
- Pg.38/106 38
- Pg.40/106 40
- Pg.42/106 42
- Enter the programming 42
- Pg.44/106 44
- Pg.46/106 46
- GRAPH: AUTOMATIC CHANGE OVER 46
- HOW THE CIRCUIT 1 OR 2 47
- 15 CUSTOM DISPLAY 48
- Pg.50/106 50
- HOW THE SET POINT VALUE 51
- ODIFY THE SET POINT 51
- 16.4 DISPLAY IN REMOTE OFF 52
- 17 FUNCTION MENU “ M” KEY 52
- 18 ENERGY SAVING 56
- 19 DYNAMIC SETPOINT 57
- 19.1 DYNAMIC SETPOINT GRAPH 58
- 20 AUXILIARY RELAYS 59
- Pg.60/106 60
- /RECOVERY 62
- 27 COMPRESSORS 64
- 27.1 COMPRESSORS START- UP 64
- 27.2 DIRECT START- UP 64
- 27.4 PART WINDING 65
- 27.7 STAR - DELTA START 65
- 28 CAPACITY CONTROL 66
- 28.1 MINIMUM LOAD START- UP 67
- 29 PUMP DOWN 68
- ACTIVATION 69
- UMP DOWN INFORMATION 70
- NLOADING DESCRIPTION 70
- NLOADING INFORMATION 70
- Pg.72/106 72
- FA26 Hot start differential 73
- 36 LOAD MAINTENANCE 74
- 37 CONDENSER FAN REGULATION 74
- OUTPUT FOR FAN CONTROL 75
- Pg.76/106 76
- 38 DEFROST CYCLE 77
- 38.1 FORCED DEFROST 77
- 38.2 COMBINED DEFROST 77
- 38.3 MANUAL DEFROST 78
- EFROST PARAMETER DESCRIPTION 79
- Pg.80/106 80
- 39 RECOVERY 81
- THE RECOVERY CYCLE 82
- 40.1 RECOVERY DISABLED 82
- AEFL evaporator flow alarm 83
- NOTE ABOUT THE FLOW ALARM 83
- 41.7 AEE EEPROM ALARM 84
- Significato label display 85
- 41.11 ARTF CLOCK FAILURE 86
- 41.12 ARTC CLOCK ALARM 87
- Pg.88/106 88
- Pg.90/106 90
- - PRESSURE SWITCH ALARM / 90
- Pg.92/106 92
- 41.38 ALARM RELAY AND BUZZER 94
- 41.39 KEYABOARD ALARM 94
- Pg.96/106 96
- Alarm description 96
- 44 BLACK-OUT 98
- 45 INSTALLING AND MOUNTING 98
- 45.1 PANEL CUT- OUT 98
- 45.4 METAL FRONT FRAME 99
- 46 ELECTRICAL CONNECTIONS 100
- 47 ACCESSORIES 100
- 47.3 TRANSFORMER 101
- 48 TECHNICAL DATA 102
Kommentare zu diesen Handbüchern
Verwandte Produkte und Handbücher für Vernetzung Emerson X-web300
Vernetzung Emerson X-web500 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
(166 Seiten)
Vernetzung Emerson FM-3 Spezifikationen
(110 Seiten)
(110 Seiten)
Vernetzung Emerson FM-3 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Vernetzung Emerson Liebert CW Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Vernetzung Emerson FM-3 Betriebsanweisung
(263 Seiten)
(263 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med