Emerson X-web300 Bedienungsanleitung Seite 88
- Seite / 102
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1592015300 User manual iCHILL 200 L GB r1.3 09/09/2005
Pg.88/106
41.16 ACP1 - ACP12 CONDENSER PUMPS MAINTENANCE REQUEST
Label description
ACP1 (main water pump)
ACP2 (support water pump)
Activation Load running hours > counter setpoint for that load
Reset Running hour reset (Hour label in Menu function)
Restart
Manual
Icon
blinking
Actions
Alarm relay and buzzer activated
REGULATION
Actions Only signalling
Loads Not modified
41.17 B1HP - B2HP HIGH PRESSURE SWITCH CIRCUIT 1 AND 2
Label on display b1HP (high pressure switch circuit #1)
b2HP (high pressure switch circuit #2)
Reason The unit is running and the digital input of the high pressure switch is active
Reset Digital input not active
Restart Manual (Reset procedure in Menu function)
Icon
blinking
Action Alarm Relay + and buzzer on
Regulation
Condensing fan Maximum speed for 60 seconds
41.18 B1LP - B2LP LOW TEMPERATURE / LOW CONDENSING PRESSURE OF THE CIRCUIT
Label o the display b1lP (low pressure digital input of the circuit 1)
b2lP (low pressure digital input of the circuit 2)
Origin
When the condensing probe value is lower than AL03 setpoint if:
• In chiller or heat pump
• Stand-by o remote OFF when AL08 = 1
• In defrost when AL06=1
The alarm is not signalled if:
• In defrost ,for the time AL07, when the 4-way valve is turned on.
• For the time set in AL01 after turning on the compressor.
Reset When the condensing probe temperature is higher than AL03 + AL04 (differential)
Restart Automatic– Manual after AL05 events per hour (Reset procedure in Menu function).
Icon
Blinking
Action
Alarm Relay + and buzzer on
41.19 B1AC - B2AC - B1AC - B2AC ANTIFREEZE ALARM / LOW OUTLET TEMPERATURE
(AIR / AIR UNIT IN CHILLER MODE)
Label o the display b1AC (anti-freeze alarm of the circuit #1 in chiller)
b2AC (anti-freeze alarm of the circuit #2 in chiller)
b1Ac (anti-freeze alarm signalling of the circuit #1 in chiller)
b2Ac (anti-freeze alarm signalling of the circuit #2 in chiller)
Both the labels are displayed when the alarm is coming from the evaporator inlet probe or
evaporator common outlet probe or when there is only one digital input configured.
Origin
Normal conditions, stand-by, remote OFF: when the anti-freeze probe value is lower than AL26 for
AL28 seconds.
With the anti-freeze digital input is active.
Reset
When the anti-freeze probe value is higher than A26+ AL27(differential)
With the anti-freeze digital input is active.
Restart Automatic – Manual after AL29 events per hours (Reset procedure in Menu function).
Icon
Blinking
Action If AL30=0 only the compressors are turned off and than display shows b1Ac b2Ac, the buzzer and
the alarm relay are not activated.
If AL30=0 only the compressors are turned off and than display shows b1Ac b2Ac, the buzzer and
the alarm relay are activated.
If the alarm comes from the digital input also the anti-freeze heaters are turned on.
- DIXELL 1
- INDEX 2
- 4
- 1 GENERAL ADVICE 7
- 2 GENERAL FEATURES 8
- 2.1 MAIN FUNCTION 8
- Pg.10/106 10
- 4 USER INTERFACE 11
- Pg.12/106 12
- 4.4 KEY FUNCTION 14
- 4.5 KEY COMBINANTION 15
- 4.6 LED AND ICONS 15
- 4.7 DISPLAY AND ICONS 16
- 5 REMOTE TERMINAL 17
- 6 FIRST INSTALLING 17
- 6.2 RTC SETUP 17
- 7 WIRING CONNECTIONS 18
- 7.4 DIGITAL INPUTS 19
- Pg.20/106 20
- Pg.22/106 22
- 7.12 HOT KEY 64 CONNECTION 23
- 7.13 XJ485 CONNECTION 23
- Pg.24/106 24
- Pg.26/106 26
- 8.7 OTHER OUTPUTS 27
- 9 TABLE OF THE PARAMETERS 28
- Pg.30/106 30
- Pg.32/106 32
- Pg.34/106 34
- Pg.36/106 36
- Pg.38/106 38
- Pg.40/106 40
- Pg.42/106 42
- Enter the programming 42
- Pg.44/106 44
- Pg.46/106 46
- GRAPH: AUTOMATIC CHANGE OVER 46
- HOW THE CIRCUIT 1 OR 2 47
- 15 CUSTOM DISPLAY 48
- Pg.50/106 50
- HOW THE SET POINT VALUE 51
- ODIFY THE SET POINT 51
- 16.4 DISPLAY IN REMOTE OFF 52
- 17 FUNCTION MENU “ M” KEY 52
- 18 ENERGY SAVING 56
- 19 DYNAMIC SETPOINT 57
- 19.1 DYNAMIC SETPOINT GRAPH 58
- 20 AUXILIARY RELAYS 59
- Pg.60/106 60
- /RECOVERY 62
- 27 COMPRESSORS 64
- 27.1 COMPRESSORS START- UP 64
- 27.2 DIRECT START- UP 64
- 27.4 PART WINDING 65
- 27.7 STAR - DELTA START 65
- 28 CAPACITY CONTROL 66
- 28.1 MINIMUM LOAD START- UP 67
- 29 PUMP DOWN 68
- ACTIVATION 69
- UMP DOWN INFORMATION 70
- NLOADING DESCRIPTION 70
- NLOADING INFORMATION 70
- Pg.72/106 72
- FA26 Hot start differential 73
- 36 LOAD MAINTENANCE 74
- 37 CONDENSER FAN REGULATION 74
- OUTPUT FOR FAN CONTROL 75
- Pg.76/106 76
- 38 DEFROST CYCLE 77
- 38.1 FORCED DEFROST 77
- 38.2 COMBINED DEFROST 77
- 38.3 MANUAL DEFROST 78
- EFROST PARAMETER DESCRIPTION 79
- Pg.80/106 80
- 39 RECOVERY 81
- THE RECOVERY CYCLE 82
- 40.1 RECOVERY DISABLED 82
- AEFL evaporator flow alarm 83
- NOTE ABOUT THE FLOW ALARM 83
- 41.7 AEE EEPROM ALARM 84
- Significato label display 85
- 41.11 ARTF CLOCK FAILURE 86
- 41.12 ARTC CLOCK ALARM 87
- Pg.88/106 88
- Pg.90/106 90
- - PRESSURE SWITCH ALARM / 90
- Pg.92/106 92
- 41.38 ALARM RELAY AND BUZZER 94
- 41.39 KEYABOARD ALARM 94
- Pg.96/106 96
- Alarm description 96
- 44 BLACK-OUT 98
- 45 INSTALLING AND MOUNTING 98
- 45.1 PANEL CUT- OUT 98
- 45.4 METAL FRONT FRAME 99
- 46 ELECTRICAL CONNECTIONS 100
- 47 ACCESSORIES 100
- 47.3 TRANSFORMER 101
- 48 TECHNICAL DATA 102
Kommentare zu diesen Handbüchern
Verwandte Produkte und Handbücher für Vernetzung Emerson X-web300
Vernetzung Emerson X-web500 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
(166 Seiten)
Vernetzung Emerson FM-3 Spezifikationen
(110 Seiten)
(110 Seiten)
Vernetzung Emerson FM-3 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Vernetzung Emerson Liebert CW Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Vernetzung Emerson FM-3 Betriebsanweisung
(263 Seiten)
(263 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med