Emerson X-web300 Bedienungsanleitung Seite 91
- Seite / 102
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1592015300 User manual iCHILL 200 L GB r1.3 09/09/2005
Origin
The compressor discharge temperature is higher than AL39 setpoint.
ATTENTION
The display resolution is 0.1°C until the read-out is 99.9, over 100°C it is 1°C.
Reset If the probe value of the high discharge temperature is lower than “AL39 - AL40 (differential)”
Restart Automatic. Manual when there are AL41 per hour (Reset procedure in Menu function).
Icon
Blinking
Action Alarm Relay + and buzzer on
41.28 C1TR - C2TR - C3TR - C4TR - C5TR - C6TR COMPRESSOR OVERLOAD ALARM
Label o the display C1tr (Compressor #1 overload alarm) -…C6tr (Compressor #1 overload alarm 6)
Origin With active digital input
The alarm is not detected within the AL19 time delay after the on compressor
Reset When the digital input is not active
Restart Manual after AL20 events/hour, to reset the alarm enter the function menu under cOtr.
Icon
Blinking
Action Alarm relay + buzzer ON
Compressor involved If AL47=0 or 1: OFF
Compressor not involved If AL47=0: it follows its regulation. If AL47=1: OFF
ATTENTION
The parameter AL47 determines the functioning of the overload alarm of the compressors.
If AL47 = 0 single compressor locked when its digital input protection is active, on the display the corresponding alarm message.
If AL47 = 1 all the circuit of the compressor is locked when one digital input protection is active, on the display the corresponding alarm
message.
41.29 B1DF – B2DF DEFROST ALARM
Label o the display b1dF (Defrost alarm of the circuit #1)
b2dF (Defrost alarm of the circuit #2)
Origin Only in defrost if DF01 = 1,3 (defrost en temperature/pressure or external contact): when the
defrost ends after the DF05 timeout.
Reset Stand - by or remote ON-OFF.
Next defrost ends for temperature/pressure.
Restart Automatic if next defrost ends for temperature/pressure, otherwise manual.
Icon
Blinking
Action Alarm relay + buzzer OFF
41.30 B1CU – B2CU UNLOADING DISABLED FROM HIGH CONDENSING TEMPERATURE /
PRESSURE IN CHILLER
Label o the display b1CU (unloading high temperature from condenser of the circuit # 1)
b2CU (unloading high temperature from condenser of the circuit # 2)
Origin When the temperature/pressure of condenser probe control is higher then CO44
Reset When the temperature/pressure of condenser probe is lower than CO44 –CO45
(differential)
After unloading is activated and after Par. CO47
Restart Automatic
Icon
Blinkin
Action Alarm relay + buzzer OFF
41.31 B1CU – B2CU: UNLOADING FROM LOW CONDENSING TEMPERATURE / PRESSURE IN
HEAT PUMP
Label o the display b1CU (unloading message from condenser #1)
b2CU (unloading message from condenser #2)
Origin During normal running condition when the temperature/pressure of evaporator/condenser probe is
lower than < CO46 setpoint
Reset when the temperature/pressure of evaporator/condenser probe value is higher than
CO46 + CO47
After unloading is activated and after Par. CO48
Restart Automatic
Icon
Blinking
Action Alarm relay + buzzer OFF
- DIXELL 1
- INDEX 2
- 4
- 1 GENERAL ADVICE 7
- 2 GENERAL FEATURES 8
- 2.1 MAIN FUNCTION 8
- Pg.10/106 10
- 4 USER INTERFACE 11
- Pg.12/106 12
- 4.4 KEY FUNCTION 14
- 4.5 KEY COMBINANTION 15
- 4.6 LED AND ICONS 15
- 4.7 DISPLAY AND ICONS 16
- 5 REMOTE TERMINAL 17
- 6 FIRST INSTALLING 17
- 6.2 RTC SETUP 17
- 7 WIRING CONNECTIONS 18
- 7.4 DIGITAL INPUTS 19
- Pg.20/106 20
- Pg.22/106 22
- 7.12 HOT KEY 64 CONNECTION 23
- 7.13 XJ485 CONNECTION 23
- Pg.24/106 24
- Pg.26/106 26
- 8.7 OTHER OUTPUTS 27
- 9 TABLE OF THE PARAMETERS 28
- Pg.30/106 30
- Pg.32/106 32
- Pg.34/106 34
- Pg.36/106 36
- Pg.38/106 38
- Pg.40/106 40
- Pg.42/106 42
- Enter the programming 42
- Pg.44/106 44
- Pg.46/106 46
- GRAPH: AUTOMATIC CHANGE OVER 46
- HOW THE CIRCUIT 1 OR 2 47
- 15 CUSTOM DISPLAY 48
- Pg.50/106 50
- HOW THE SET POINT VALUE 51
- ODIFY THE SET POINT 51
- 16.4 DISPLAY IN REMOTE OFF 52
- 17 FUNCTION MENU “ M” KEY 52
- 18 ENERGY SAVING 56
- 19 DYNAMIC SETPOINT 57
- 19.1 DYNAMIC SETPOINT GRAPH 58
- 20 AUXILIARY RELAYS 59
- Pg.60/106 60
- /RECOVERY 62
- 27 COMPRESSORS 64
- 27.1 COMPRESSORS START- UP 64
- 27.2 DIRECT START- UP 64
- 27.4 PART WINDING 65
- 27.7 STAR - DELTA START 65
- 28 CAPACITY CONTROL 66
- 28.1 MINIMUM LOAD START- UP 67
- 29 PUMP DOWN 68
- ACTIVATION 69
- UMP DOWN INFORMATION 70
- NLOADING DESCRIPTION 70
- NLOADING INFORMATION 70
- Pg.72/106 72
- FA26 Hot start differential 73
- 36 LOAD MAINTENANCE 74
- 37 CONDENSER FAN REGULATION 74
- OUTPUT FOR FAN CONTROL 75
- Pg.76/106 76
- 38 DEFROST CYCLE 77
- 38.1 FORCED DEFROST 77
- 38.2 COMBINED DEFROST 77
- 38.3 MANUAL DEFROST 78
- EFROST PARAMETER DESCRIPTION 79
- Pg.80/106 80
- 39 RECOVERY 81
- THE RECOVERY CYCLE 82
- 40.1 RECOVERY DISABLED 82
- AEFL evaporator flow alarm 83
- NOTE ABOUT THE FLOW ALARM 83
- 41.7 AEE EEPROM ALARM 84
- Significato label display 85
- 41.11 ARTF CLOCK FAILURE 86
- 41.12 ARTC CLOCK ALARM 87
- Pg.88/106 88
- Pg.90/106 90
- - PRESSURE SWITCH ALARM / 90
- Pg.92/106 92
- 41.38 ALARM RELAY AND BUZZER 94
- 41.39 KEYABOARD ALARM 94
- Pg.96/106 96
- Alarm description 96
- 44 BLACK-OUT 98
- 45 INSTALLING AND MOUNTING 98
- 45.1 PANEL CUT- OUT 98
- 45.4 METAL FRONT FRAME 99
- 46 ELECTRICAL CONNECTIONS 100
- 47 ACCESSORIES 100
- 47.3 TRANSFORMER 101
- 48 TECHNICAL DATA 102
Kommentare zu diesen Handbüchern
Verwandte Produkte und Handbücher für Vernetzung Emerson X-web300
Vernetzung Emerson X-web500 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
(166 Seiten)
Vernetzung Emerson FM-3 Spezifikationen
(110 Seiten)
(110 Seiten)
Vernetzung Emerson FM-3 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Vernetzung Emerson Liebert CW Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Vernetzung Emerson FM-3 Betriebsanweisung
(263 Seiten)
(263 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med