Emerson X-web300 Bedienungsanleitung Seite 52
- Seite / 102
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1592015300 User manual iCHILL 200 L GB r1.3 09/09/2005
Pg.52/106
16.4 DISPLAY IN REMOTE OFF
From digital input configured as remote ON/OFF: the active input sets the unit in OFF (even when the unit is a motocondensing unit).
The top display shows “OFF ”, the led of the decimal point is blinking.
16.5 DISPLAY IN MOTOCONDENSING CONFIGURATION
The top display shows “ON” for active input and “OFF” for not active input. If the unit is running in Chiller the top display shows OnC
otherwise OnH for heat pump.
The configuration for motocondensing, as for chiller or HP, allows to show through the top and the bottom display all the detected input
measurements and alarms.
17 FUNCTION MENU “ M” KEY
The function Menu is composed of the following items:
1) Show and reset the alarms ALrM
2) Compressor overload alarm reset COtr
3) Show and reset the alarm log ALOG
4) Upload the parameter into the Hot Key UPL
5) Enable – disable one or the two circuits CrEn
6) Enable – disable one of the compressors COEn
7) Display the compressor discharge temperature COdt
8) Show and reset the number of compressor running hour Hour
9) Show and reset the number of compressor starts-up COSn
10) Show the condensing fan speed percentage of the proportional output Cond
11) Show the percentage of the proportional output 0 ÷ 10 Vdc Pout
12) Time counting to next defrost cycle, under heat pump mode, dF
13) Show the probe temperatures that enabled to control the auxiliary output uS
14)
Show the probe the temperature of the remote panels trEM
MENU FUNCTION ACCESS: Push and release the M key.
MENU FUNCTION ACCESS: Push and release the M key or wait the 15seconds timeout limit.
With the UP or DOWN keys move inside the label list.
17.1 ALARM LIST: SHOW AND RESET
ALrM FUNCTION
Enter the function MENU pushing M key one time
1) Use the UP or DOWN to select the AlrM label
2) Push SET key (Nothing happens if there are no active alarm events)
3) Bottom display: alarm label code. Top display: label rSt to reset or NO if it is not possible.
4) Use the UP or DOWN to scroll the alarm list.
5) Pushing SET when the rSt label is displayed the corresponding alarm will be reset, then the display shows next alarm in the
list, pushing SET again the alarm is reset and the display shows next alarm etc. Nothing happens by pushing SET when the
label NO is displayed, in this case push UP or DOWN to move to another alarm label.
6) To exit the ALrM reset function push MENU one time or wait the timeout.
17.2 COMPRESSOR OVERLOAD ALARM RESET
COtr function resets the compressor overload alarm event.
Within the COtr function all the active compressor overload alarms are displayed in a list.
Labels involved in COtr: CO1r = compressor 1 overload reset … CO6r = compressor 6 overload reset. Labels CO1r – CO2r – CO3r
– CO4r – CO5r - CO6r are available if the digital inputs have been previously configured.
ATTENTION
In the COtr function the alarm is displayed only after the number of events per hour have reched the Par. AL20 value,only after that
number of events per hour the alarm becomes MANUAL.
MANUAL ALARM RESET PROCEDURE
Enter Menu function
1. Use UP or DOWN key and select the COtr on the bottom display.
2. Push SET one time, if there are active alarms the bottom display shows the alarm label eg. CO1r (for compressor 1) while the
top display shows the label rSt to reset the alarm or NO if the alarm can not be reset. Use the UP or DOWN keys to scroll all
the alrm list.
3. Nothing happens by pushing SET when the label NO is displayed.
4. Pushing SET when the rSt label is displayed the corresponding alarm will be reset after the password: bottom display = ArSt
while the top display = PAS.
5. Push SET and the top display blinks 0 while the bottom shows PAS. Insert the password using UP or DOWN key (see AL
parameter family). If the password is OK the ArSt blinks for per 3seconds, if the password value is not correct the top display
blinks 0 while the bottom shows PAS. If within 5 seconds no value is inserted the display label come back to CO1r function.
6. To exit the COtr function push MENU or wait the timeout.
- DIXELL 1
- INDEX 2
- 4
- 1 GENERAL ADVICE 7
- 2 GENERAL FEATURES 8
- 2.1 MAIN FUNCTION 8
- Pg.10/106 10
- 4 USER INTERFACE 11
- Pg.12/106 12
- 4.4 KEY FUNCTION 14
- 4.5 KEY COMBINANTION 15
- 4.6 LED AND ICONS 15
- 4.7 DISPLAY AND ICONS 16
- 5 REMOTE TERMINAL 17
- 6 FIRST INSTALLING 17
- 6.2 RTC SETUP 17
- 7 WIRING CONNECTIONS 18
- 7.4 DIGITAL INPUTS 19
- Pg.20/106 20
- Pg.22/106 22
- 7.12 HOT KEY 64 CONNECTION 23
- 7.13 XJ485 CONNECTION 23
- Pg.24/106 24
- Pg.26/106 26
- 8.7 OTHER OUTPUTS 27
- 9 TABLE OF THE PARAMETERS 28
- Pg.30/106 30
- Pg.32/106 32
- Pg.34/106 34
- Pg.36/106 36
- Pg.38/106 38
- Pg.40/106 40
- Pg.42/106 42
- Enter the programming 42
- Pg.44/106 44
- Pg.46/106 46
- GRAPH: AUTOMATIC CHANGE OVER 46
- HOW THE CIRCUIT 1 OR 2 47
- 15 CUSTOM DISPLAY 48
- Pg.50/106 50
- HOW THE SET POINT VALUE 51
- ODIFY THE SET POINT 51
- 16.4 DISPLAY IN REMOTE OFF 52
- 17 FUNCTION MENU “ M” KEY 52
- 18 ENERGY SAVING 56
- 19 DYNAMIC SETPOINT 57
- 19.1 DYNAMIC SETPOINT GRAPH 58
- 20 AUXILIARY RELAYS 59
- Pg.60/106 60
- /RECOVERY 62
- 27 COMPRESSORS 64
- 27.1 COMPRESSORS START- UP 64
- 27.2 DIRECT START- UP 64
- 27.4 PART WINDING 65
- 27.7 STAR - DELTA START 65
- 28 CAPACITY CONTROL 66
- 28.1 MINIMUM LOAD START- UP 67
- 29 PUMP DOWN 68
- ACTIVATION 69
- UMP DOWN INFORMATION 70
- NLOADING DESCRIPTION 70
- NLOADING INFORMATION 70
- Pg.72/106 72
- FA26 Hot start differential 73
- 36 LOAD MAINTENANCE 74
- 37 CONDENSER FAN REGULATION 74
- OUTPUT FOR FAN CONTROL 75
- Pg.76/106 76
- 38 DEFROST CYCLE 77
- 38.1 FORCED DEFROST 77
- 38.2 COMBINED DEFROST 77
- 38.3 MANUAL DEFROST 78
- EFROST PARAMETER DESCRIPTION 79
- Pg.80/106 80
- 39 RECOVERY 81
- THE RECOVERY CYCLE 82
- 40.1 RECOVERY DISABLED 82
- AEFL evaporator flow alarm 83
- NOTE ABOUT THE FLOW ALARM 83
- 41.7 AEE EEPROM ALARM 84
- Significato label display 85
- 41.11 ARTF CLOCK FAILURE 86
- 41.12 ARTC CLOCK ALARM 87
- Pg.88/106 88
- Pg.90/106 90
- - PRESSURE SWITCH ALARM / 90
- Pg.92/106 92
- 41.38 ALARM RELAY AND BUZZER 94
- 41.39 KEYABOARD ALARM 94
- Pg.96/106 96
- Alarm description 96
- 44 BLACK-OUT 98
- 45 INSTALLING AND MOUNTING 98
- 45.1 PANEL CUT- OUT 98
- 45.4 METAL FRONT FRAME 99
- 46 ELECTRICAL CONNECTIONS 100
- 47 ACCESSORIES 100
- 47.3 TRANSFORMER 101
- 48 TECHNICAL DATA 102
Kommentare zu diesen Handbüchern
Verwandte Produkte und Handbücher für Vernetzung Emerson X-web300
Vernetzung Emerson X-web500 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
(166 Seiten)
Vernetzung Emerson FM-3 Spezifikationen
(110 Seiten)
(110 Seiten)
Vernetzung Emerson FM-3 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Vernetzung Emerson Liebert CW Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Vernetzung Emerson FM-3 Betriebsanweisung
(263 Seiten)
(263 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med