Emerson MICRO MOTION 2700 Installationshandbuch Seite 117
- Seite / 264
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Transmitter Configuration and Use: Series 1000 and 2000 Transmitters 107
Pressure Compensation, Temperature Compensation, and Polling continued
Troubleshooting DiagramsDefaultsCompensation
4. If you will use a static temperature value:
a. Ensure that polling for temperature is not configured. Polling for pressure is allowed. See
Section 9.4.
b. From the
ProLink menu, open the Configuration panel and click the Temperature tab.
c. Enter the temperature value in the
External Temperature box.
5. Click
Apply.
With a Communicator
To configure external temperature compensation with a Communicator:
1. Press
4, 1.
2. Select
Ext Temp.
a. Select
Enable Ext Temp.
b. Select
Enabled.
c. Press ENTER.
3. If you will poll an external device for temperature data:
a. Press SEND.
b. Press
HOME.
c. Ensure that the transmitter is configured to use the same temperature measurement unit
that the external temperature measurement device uses (see Section 6.4).
d. Follow the polling setup instructions in Section 9.4.
4. If you will use a static temperature value:
a. Ensure that polling for temperature is not configured. Polling for pressure is allowed. See
Section 9.4.
b. Select
Static temperature.
c. Enter the static temperature value.
d. Press ENTER.
e. Press SEND.
f. Press HOME.
9.4 Configuring polling
Polling is used to retrieve temperature or pressure data from an external device.
• If you have core processor v2.1 and earlier, the polled temperatuare value is
used for all calculations that require a temperature value.
• If you have core processor v2.2 or later, the polled temperature value is used
only for calculation of the derived variable in enhanced density applications
or the CTL value in petroleum measurement applications. The temperature
value from the sensor is used for all other calculations that require a
temperature value.
You may query one or two external devices.
Polling requires HART protocol over the Bell 202 physical layer. You must ensure that the primary
mA output has been wired for HART protocol. See the installation manual for your transmitter.
You can configure polling with ProLink II or the Communicator.
• Model 1500 AN
• Model 1700 AN
• Model 1700 IS
• Model 2500 CIO
• Model 2700 AN
• Model 2700 IS
• Model 2700 CIO
- Micro Motion 1
- Series 1000 and 1
- Series 2000 Transmitters 1
- Contents 5
- Chapter 1 11
- Before You Begin 11
- Before You Begin continued 13
- Topic Document 13
- Term Definition 13
- Item Configuration data 15
- Chapter 2 17
- Using the Transmitter Display 17
- –8.100E 5 19
- Chapter 3 21
- Poll button in the Connect 26
- 1 and 2, or to the 26
- Connect to Device 32
- Chapter 4 33
- 375 Field Communicator 33
- Chapter 5 39
- Flowmeter Startup 39
- Flowmeter Startup continued 40
- 5.5.3 Zeroing with ProLink II 50
- Chapter 6 53
- Sensor type 54
- T- S er ie s O t he r 54
- Newer tag Older tag 55
- Flow FCF X.XXXX FT X.XX 56
- Terminals 58
- Default Process 58
- Mass flow unit 60
- Volume flow unit 61
- ProLink II code 69
- Communicator 69
- Polarity 75
- Output power 75
- Description 75
- Assignment ProLink II code 77
- Using the Transmitter 79
- Chapter 7 79
- • Model 1700 AN 84
- • Model 1700 IS 84
- • Model 2700 AN 84
- • Model 2700 IS 84
- • Model 2700 CIO 84
- Scroll optical switch 85
- Select optical switch 85
- Function name Communicator 86
- ProLink II 86
- ProLink 87
- Totalizer Control 87
- With a Communicator 88
- Chapter 8 89
- Optional Configuration 89
- Table 8-1 Configuration map 90
- Special 92
- • Model 2500 CIO 93
- Variable Description 94
- Cutoff type Default Comments 96
- Example 1 100
- Example 2 100
- Example 3 101
- Informational panel of the 102
- Status window 102
- Scroll to view process 104
- Max Int. Totalizers stop 106
- Parameter 109
- Series 1000 Series 2000 110
- Process variable 110
- PV SV TV QV PV SV TV QV 110
- Parameter Description 111
- Chapter 9 113
- Compensation, and Polling 113
- Pressure unit 114
- Static pressure 116
- Polled Var 1 119
- Chapter 10 121
- Troubleshooting 121
- Troubleshooting continued 122
- Section Topic 122
- Symptom Cause Possible remedy 132
- Pickoff value 141
- Cause Possible remedy 141
- Test terminal pair 146
- Colors Numbers 146
- Possible cause Solution 147
- Appendix A 151
- Default Values and Ranges 151
- Appendix B 155
- Appendix C 167
- Calibrating the Transmitter 167
- Appendix D 175
- Name Description 176
- Available process variables 178
- Slope and offset 181
- Appendix E 183
- Other configuration options 185
- Preferences menu 187
- Figure E-4 Communicator menus 188
- Appendix F 193
- Figure F-4 Communicator menus 197
- Appendix G 203
- Transmitters 203
- Figure G-4 Communicator menus 207
- Enter password if required 212
- Appendix H 219
- Figure H-4 Communicator menus 223
- Appendix I 235
- Configuration 237
- Figure I-4 Communicator menus 239
- On-Line Menu 240
- 3 Basic Setup 240
- 4 Detailed Setup 240
- 5 Review 243
- Appendix J 251
- Select to disable 252
- Select to enable 252
- Index continued 256
- *20001715* 264
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Emerson MICRO MOTION 2700
(3 Seiten)
Messen, Testen & Steuern Emerson 644 Spezifikationen
(182 Seiten)
(182 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern