Emerson CMF200A Installationshandbuch Seite 1

Micro Motion®ELITE® SensorsInstallation ManualInstallation ManualP/N 20002158, Rev. CSeptember 2007

8 Micro Motion® ELITE® SensorsDetermining a Location Figure 6 High-temperature and extreme high-temperature ELITE sensor ambient and process temperatu

Installation Manual 9Determining a LocationMaximum wiring distancesIf the transmitter is mounted remotely from the sensor, the maximum distance betwee

10 Micro Motion® ELITE® SensorsOrienting the Sensor Step 2 Orienting the SensorThe sensor will function properly in any orientation if the sensor tube

Installation Manual 11Mounting the SensorStep 3 Mounting the SensorUse your common practices to minimize torque and bending load on process connection

12 Micro Motion® ELITE® SensorsMounting the Sensor Installing extended mount electronicsIf you ordered a sensor with an extended mount for the electro

Installation Manual 13Mounting the SensorFigure 10 Mounting the temperature extender onto the sensorMounting the electronics of high-temperature and e

14 Micro Motion® ELITE® SensorsMounting the Sensor Figure 11 Electronics mounting for high-temperature and extreme high-temperature ELITE sensors Inst

Installation Manual 15Mounting the SensorFigure 12 Wafer-style assemblyFigure 13 Tightening the sensor alignment ringsProcess connectionSensor waferFl

16 Micro Motion® ELITE® SensorsWiring Step 4 WiringHazardous area installationsIf you are installing the sensor in a hazardous location, verify that t

Installation Manual 17WiringFigure 14 Micro Motion cable gland and heat shrink4. For connection at the core processor housing, prepare shielded cable

©2007, Micro Motion, Inc. All rights reserved. ELITE and ProLink are registered trademarks, and MVD and MVD Direct Connect are trademarks of Micro Mot

18 Micro Motion® ELITE® SensorsWiring Figure 16 Applying the heat shrinkg. Position gland clamping insert so the interior end is flush with the heat s

Installation Manual 19WiringFigure 19 Connecting the wires at the core processor 7. Reinstall and tighten the core processor housing cover.8. Addition

20 Micro Motion® ELITE® SensorsGrounding Step 5 GroundingThe sensor can be grounded via the piping if the joints in the pipeline are ground-bonded. If

Installation Manual 21Purge FittingsPurge FittingsIf the sensor has purge fittings, they should remain sealed at all times. After a purge plug has bee

22 Micro Motion® ELITE® SensorsRupture Disks Rupture DisksIf the sensor has rupture disks, they are installed in the sensor purge fitting openings. Th

Installation Manual 23Return PolicyReturn PolicyMicro Motion procedures must be followed when returning equipment. These procedures ensure legal compl

Micro Motion Inc. USAWorldwide Headquarters7070 Winchester CircleBoulder, Colorado 80301T +1 303-527-5200+1 800-522-6277F +1 303-530-8459Micro Motion

Installation Manual 1Before You BeginBefore You Begin This manual describes how to install a Micro Motion® ELITE® sensor. The following information is

2 Micro Motion® ELITE® SensorsBefore You Begin SpecificationsFull product specifications can be found in the product data sheet, which is available fr

Installation Manual 3Before You BeginFigure 1 ELITE sensor with Model 2400S transmitter or enhanced core processor Flow directionarrowPurge fittings o

4 Micro Motion® ELITE® SensorsBefore You Begin Figure 2 ELITE sensor with core processorFlow directionarrowPurge fittings or rupturedisks (optional)Ca

Installation Manual 5Before You BeginFigure 3 ELITE sensor with junction boxFlow directionarrowPurge connections orrupture disks(optional)Calibration

6 Micro Motion® ELITE® SensorsDetermining a Location Figure 4 High-temperature or extreme high-temperature ELITE sensorStep 1 Determining a LocationCh

Installation Manual 7Determining a LocationFigure 5 ELITE sensor ambient and process temperature limits (all models excepthigh-temperature and extreme