Emerson Y696VR Bedienerhandbuch Seite 5
- Seite / 8
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Y696VR Series
5
diaphragm head (key 24), diaphragm (key 5), and
upper diaphragm head (key 6) on the pusher post
(key 8) and attach with the hex nut (key 37).
Tighten using 30 to 45 foot-pounds (41 to 61 N•m)
of torque.
8. Install the pusher post (key 8) plus attached
diaphragm parts onto the lever assembly (key 9).
9. Install the spring case assembly (key 23) and control
spring (key 1) on the diaphragm casing (key 20) so
that the vent assembly is correctly oriented, and
secure them with the spring case cap screws
(key 21) and hex nuts (key 22), nger tight only.
10. Install the upper spring seat and the adjusting nut
(key 2) turning clockwise until there is enough
control spring force to provide proper slack to
the diaphragm (key 5) and attached parts. Using
a crisscross pattern, nish tightening the spring
case cap screws (key 21) and hex nuts (key 22)
using 55 to 75 inch-pounds (6 to 8 N•m) of
torque. Then nish turning the adjusting nut
(key 2) to the desired outlet pressure setting.
11. Install a replacement closing cap gasket (key 35)
if necessary, and then install the closing cap
(key 3).
Type Y696VRM Vacuum Regulator
1. Remove the closing cap (key 3) and turn the
adjusting nut (key 2) counterclockwise until all
compression is removed from the control spring
(key 1). If the only further maintenance is to
change the control spring (key 1), skip to step 10.
2. Remove the spring case cap screws (key 21) and
hex nuts (key 22) and remove the spring case
(key 23).
3. Remove the diaphragm (key 5) and attached parts
by tilting it so the pusher post (key 8) slips off the
lever assembly (key 9). To separate the diaphragm
(key 5) from the attached parts, unscrew the
diaphragm hex nut (key 37). If the only further
maintenance is to replace the diaphragm parts or
change the control spring (key 1), skip to step 8.
4. To replace the lever assembly (key 9), remove the
machine screws (key 11) and lever pin.
5. To replace the valve stem (key 13) or stem seal
O-ring (key 15) remove the valve stem from the
diaphragm casing.
6. Lightly grease the new stem seal O-ring (key 15)
and install on the valve stem (key 13). Install the
valve stem by pushing it into the diaphragm casing
(key 20).
7. Install the lever assembly (key 9) on the valve
stem (key 13) and secure the lever assembly
(key 9) with the machine screws (key 11).
8. Install the diaphragm head gasket (key 7), lower
diaphragm head (key 24), diaphragm (key 5),
and upper diaphragm head (key 6) on the
pusher post (key 8) and attach with the hex nut
(key 37). Tighten using 30 to 45 foot-pounds
(41 to 61 N•m) of torque.
9. Install the pusher post (key 8) plus attached
diaphragm parts onto the lever assembly (key 9).
10. Install the spring case assembly (key 23) and control
spring (key 1) on the diaphragm casing (key 20) so
that the vent assembly is correctly oriented, and
secure them with the spring case cap screws
(key 21) and hex nuts (key 22), nger tight only.
11. Turn the adjusting nut (key 2) clockwise until there
is enough control spring (key 1) force to provide
proper slack to the diaphragm (key 5) and
attached parts. Using a crisscross pattern, nish
tightening the spring case cap screws (key 21)
and hex nuts (key 22) using 55 to 75 inch-pounds
(6 to 8 N•m) of torque. Then nish turning the
adjusting nut (key 2) to the desired outlet
pressure setting.
12. Install a replacement closing cap gasket (key 35)
if necessary, and then install the closing cap
(key 3).
Parts Ordering
When corresponding with the local Sales Ofce or
about this regulator, include the type number and all
other pertinent information stamped on the closing
cap or nameplate. Specify the eleven-character part
number when ordering new parts from the following
parts list.
Verwandte Produkte und Handbücher für Nein Emerson Y696VR
Nein Emerson UPC1000LOC Datenblatt
(2 Seiten)
(2 Seiten)
Nein Emerson Y696 Datenblatt
(8 Seiten)
(8 Seiten)
Nein Emerson T208 Datenblatt
(8 Seiten)
(8 Seiten)
(1 Seiten)
Nein Emerson EZH and EZHSO Series Pressure Reducing Regulators Zeichnungen und Schaubilder
(1 Seiten)
(1 Seiten)
Nein Emerson Fisher 4320 Broschüre
(28 Seiten)
(28 Seiten)
Nein Emerson 1000CFM Datenblatt
(2 Seiten)
(2 Seiten)
Nein Emerson 54e Gebrauchsanweisung
(8 Seiten)
(8 Seiten)
Nein Emerson EZH and EZHSO Series Pressure Reducing Regulators Zeichnungen und Schaubilder
(1 Seiten)
(1 Seiten)
Nein Emerson 92S Zeichnungen und Schaubilder
(1 Seiten)
(1 Seiten)
Nein Emerson 28-105kW Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Black & Decker FS1400D Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Bohrmaschinen Black & Decker FS1400D.
Wir stellen 1 PDF-Handbücher Black & Decker FS1400D zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienerhandbuch
Kommentare zu diesen Handbüchern