Emerson LMS 1000 Installationshandbuch PDF herunterladen (Seite 141)

NetSure™ LMS Data Processing Unit

Installation Instructions, Section 5879 (Issue BA, April 7, 2014)

Spec. No: 58650500, 586505500 Code: Section 5879

Model No: LMS1000 Issue BA, April 7, 2014

[133 of 149]

Changing the LED Channel Configurations

The LED channel configurations can be changed by using the commands CONFIG. The command CONFIG is also described in

"Commands" of the User Instructions (Section 5847). Section 5847 can be accessed via the CD (Electronic Documentation Package)

furnished with your system. The command, when entered, will display a header that contains the current configuration. Then,

individually, the command will list each item that can be changed, showing the current information, and then prompting for new or

revised information to be entered. If the current information does not need to be changed, press

ENTER to continue.

Command CONFIG: If the command CONFIG is entered, the system will ask that you identify which channel you wish to modify. Another

way of entering the command is to identify the desired channel in the command line by typing the channel number after the characters

CONFIG (ex. CONFIG L1). The various information pertaining to an LED Channel that can be changed through this command is described

below. This command is available to users programmed for access to level 6 commands.

Note:

Parameters which apply only to TL1 commands/messages do not appear for configuration if the TL1 software option is not installed.

CONFIG L_

Command <6>: CONFIG L1

Type

CONFIG L1

, then press

ENTER

Channel active (Y or N)

Note:

If "Y" is entered, the system will

allow the default configuration

information of the current LED

channel to be changed as shown

below.

Type

if the channel is required to be active and

if not, then press

ENTER

If "N" was entered above, the system

responds with...

Set channel configuration to

default values? (Y or N):

Type

to change the attributes of this channel to their default values.

Note:

If ”Y” is entered, this command terminates.

If ”N” is entered, the system will allow the default configuration

information of the current LED channel to be changed as shown below.

Name:

Type the desired name for this LED channel (30 characters maximum),

then press

ENTER

Color (Red, Green, or Amber):

Type

Red

Green

, or

Amber

to specify the color the LED illuminates, then

press

ENTER

Sub-access Identifier:

This parameter applies only to TL1 commands/messages. Type the

name (20 characters maximum) of the sub-access identifier that this

channel belongs to, then press

ENTER

. The group of LMS1000 channels

monitoring a sub-entity in an NMA system should have the same

access identifier and sub-access identifier. Only alpha-numeric

characters can be entered for this parameter. TL1 uses specific values

for this parameter. Refer to TA-NWT-001360, Table 4-1.

Alarm Type (Y or N):

Type

if the alarm condition determined by this channel is required to

be recorded in the alarm log (required if System Alarm Reporting is

desired for this channel, and/or an alarm class of 1 through 8 is

assigned to this channel) when it is activated and

if not, then press

ENTER

Note:

If "Y" was entered above, the

system responds with...

System Alarm Report mode (Y or

N):

Type

if the system is required to initiate an alarm report via phone

lines if this channel alarms and

if not, then press

ENTER

Note:

If "Y" was entered above for "Alarm

Type", the system responds with...

Alarm Class Number:

Type the desired alarm class number associated with this channel, then

press

ENTER

. Alarm classes are specified with the numbers 0 through 8,

with 0 representing no alarm class.

1 2 ... 136 137 138 139 140 141 142 143 144 145 146 ... 157 158

Kommentare zu diesen Handbüchern

Keine Kommentare

Emerson LMS 1000 Installationshandbuch Seite 141

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Emerson LMS 1000