Emerson DLC3020f Bedienerhandbuch Seite 121
- Seite / 200
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Instruction Manual
D103434X012
Blocks
November 2014
119
Application Information
The configuration of an AO function block and its associated output channels depends on the specific application. A
typical configuration for the Analog Output involves the following attributes:
PV_SCALE Set the range and engineering units to values that correspond to the operation range. For the
digital level controller, PV_SCALE [11] is typically set between 0 and 100%.
BKCAL_OUT If you are using the CAS_IN [17]
connector wired from another block, wire the BKCAL_OUT [25] attribute to the other block's
BKCAL_IN [27] attribute.
IO_OPTS Set the type of tracking and action upon fault state.
SHED_OPT Set the action to be taken when the set point or output are not updated in a remote mode.
Block Errors
Table B‐26 lists conditions reported in the BLOCK_ERR [6] parameter. Conditions in italics are not applicable for the AO
block and are provided only for your reference.
Table B‐26. BLOCK_ERR Conditions
Condition Number Condition Name and Description
0 Other (NA)
1 Block Configuration Error ‐ CHANNEL and SHED_OPT set to 0
2 Link Configuration Error (NA)
3 Simulate active ‐ Simulation is enabled and the block is using a simulated value in its execution.
4 Local Override ‐ Device in fault state. Actual mode LO.
5
Device Fault State Set ‐ AO block in fault state after FSTATE_TIME because of Bad status or IFS substatus on CAS_IN or Resource
block commanded fault state.
6 Device Needs Maintenance Soon ‐ Indicates a Maintenance PlantWeb Alert condition is active if Block Error Reporting is enabled.
7 Input failure/process variable has Bad status (NA)
8 Output failure ‐ PV has bad status.
9 Memory Failure (NA)
10 Lost Static Data (NA)
11 Lost NV Data (NA)
12 Readback Check Failed (NA)
13 Device Needs Maintenance Now ‐ Indicates Failed PlantWeb Alert condition is active if Block Error Reporting is enabled.
14 Power Up ‐ This condition exists after power up until actual mode is not Out of Service.
15 Out of Service ‐ The block is in Out of Service (OOS) mode.
- FIELDVUE 1
- DLC3020f Digital Level 1
- Controller for F 1
- fieldbus 1
- Contents 3
- Scope of Manual 5
- Instrument Description 5
- Foundation Fieldbus Blocks 5
- Using This Manual 6
- Specifications 7
- Related Information 7
- Educational Services 7
- Instruction Manual 10
- 28B5536‐1 11
- Section 2 Installation2‐2‐ 13
- Lever Lock 14
- Mounting 15
- DLC3020f Orientation 16
- 20A7423‐C 18
- DIGITAL LEVEL CONTROLLER 18
- AMBIENT TEMPERATURE (_C) 19
- STANDARD TRANSMITTER 19
- 39A4070‐B 19
- Fieldbus Connections 20
- Simulate Enable Jumper 21
- GE46500‐B 22
- Section 3 Overview3‐3‐ 23
- Primary Purpose Variables 24
- Shortcuts 24
- Section 4 Configuration4‐4‐ 27
- Manual Setup 28
- Variable Configuration 29
- Sensor Limits 29
- Sensor Hardware Information 30
- Sensor Units 30
- Sensor Parameters 31
- Torque Tube 32
- Process Fluid 33
- Temperature Compensation 33
- View Fluid Density Table 34
- Display Option 34
- Decimal Places 34
- Display Primary Value Offset 35
- Scrolling Message Control 35
- Snap Acting Control 35
- Primary Value 35
- Primary Value Percent 36
- DI1 Trip Point Settings 36
- DI2 Trip Point Settings 36
- Write Alarm 37
- Block Alarm 37
- Write Lock 37
- Confirm Time 38
- Communication Timeout 38
- Function Block Available 38
- Transducer Block 39
- Features Selected 39
- Alert Key 39
- Maximum Alerts Allowed 39
- Alert Setup 40
- PlantWeb Alerts 41
- Electronics 41
- Operational 41
- Rate Limit 41
- Calibration in Use 43
- Calibrate Instrument 44
- Full Calibration 45
- Trim Current Calibration 46
- Alert Conditions 47
- Variables 48
- Run Time Extremes 49
- Simulate 50
- Calibration Setup/Logs 51
- Instrument Display Test 52
- Restart Device 52
- Tools Required 53
- LCD Meter Assembly 55
- Removing the LCD Meter 56
- Replacing the LCD Meter 56
- Electronics Module 57
- Terminal Box 58
- Assembly 59
- Lever Assembly 60
- Packing for Shipment 61
- Instrument Troubleshooting 62
- Section 8 Parts8‐8‐ 65
- Parts Kits 66
- Parts List 66
- Transducer Assembly 68
- (figure 8‐2) 68
- Terminal Box Assembly 69
- (figure 8‐3) 69
- Terminal Box Cover Assembly 69
- (figure 8‐4) 69
- 28B5741‐B 70
- 29B8444‐A 71
- 29B8445 B 71
- Yamatake NQP Sensor 72
- Foxboro‐Eckardt Sensors 72
- 249 SENSOR (SIDE VIEW) 73
- FIELDBUS‐FBUS_31A 75
- FIELDBUS‐FBUS_03A 77
- Signal Conversion 78
- Advanced Features 79
- AI Block Parameter List 81
- TRANSDUCER_STATUS 9.3 RO 0 82
- UNACKNOWLEDGED 22.2 RO ALL 83
- PID Function Block 87
- Filtering 90
- Feedforward Calculation 91
- Output Tracking 91
- Set Point Tracking 91
- Reverse and Direct Action 92
- PID Block Parameter List 94
- 3=Active reported 97
- 4=Active not reported 97
- Unacknowledged 100
- T_AUTO_HYSTERESIS 101
- View Lists 102
- Status Handling 107
- I/O Selection 107
- Block Initialization 107
- Field Value Processing 108
- Alarm Detection 108
- Block Errors 109
- Action on Failure 109
- Simulation 109
- Mode Handling 116
- Shed With Return Options 117
- Shed With No Return Options 117
- Setting the Output 118
- Action On Fault Detection 119
- I/O Options 120
- Application Information 121
- CAP_STDDEV 125
- Limit Propagation 130
- Substatus Propagation 130
- STATUS_OPTS Supported 130
- SELECT_TYPE Must 132
- Input Selection 133
- Supported Modes 143
- Block Execution 144
- Advanced Topics 146
- Troubleshooting 148
- Resource Block 152
- AUTO 0 to 65535 0 159
- AUTO 1 to 255 1 159
- AUTO 3:AUTO 159
- AUTO 0 to 15 2 168
- Transducer Block (LCD) 174
- Function Block Overview 181
- Resource Blocks 182
- Transducer Blocks 182
- Block Modes 183
- Explanation of Modes 184
- Device Descriptions 185
- Status Propagation 186
- Network Communication 187
- Scheduled Transfers 188
- Unscheduled Transfers 189
- Network Management 190
- Glossary 191
- D103434X012 192
- November 2014 192
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Emerson DLC3020f
(35 Seiten)
(3 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern